Skip to the metallurgy engine
StalGuard PRO

Factory Production Control · Welding engineering

Certificate checked
before the steel
goes into production.

StalGuard PRO reads EN 10204 inspection documents, compares them with the order and the product standard, calculates CEV and CET, warns about reactive steel for galvanizing and issues a decision: release the batch with a QR label or block it with an NCR report.

Standards supported by the system

  • EN 1090-1/-2
  • EN ISO 3834
  • EN 10204
  • EN 10025
  • EN 1011-2
  • EN ISO 14713-2
  • EN ISO 9606-1
  • EN ISO 17637

Where control slips today

A non-conformity surfaces at the audit or at the galvanizer. Too late.

Each of these points is a real cost: downtime, a coating claim, a remark from the notified body. StalGuard moves control to the moment the material is received.

Comparison of traditional control and StalGuard PRO
Certificate verificationTraditionalManual retyping from PDF, comparing “by eye”.StalGuard PROAutomatic reading and comparison with the product standard and the order.
Reactive steelTraditionalUsually not checked. The problem shows up as a grey, brittle coating.StalGuard PROCategory A–D per ISO 14713-2 and a warning before the parts are sent to the galvanizer.
FPC auditTraditionalDays spent assembling binders.StalGuard PRODigital quality dossier and receiving register ready for export.
TraceabilityTraditionalChalk or marker, washed off by rain.StalGuard PRODurable QR labels linked to the heat (EN 1090-2, clause 5.2).

Metallurgy engine · demo version

Enter the certificate data. The result is calculated live.

The same logic that StalGuard PRO applies to the documents it reads: CEV and CET per EN 1011-2, comparison with EN 10025-2, galvanizing reactivity per EN ISO 14713-2 and inspection document type check. All calculations run only in your browser.

01 · DELIVERY AND EXECUTION CLASS
02 · CHEMICAL COMPOSITION FROM THE CERTIFICATE [%]

Comma or dot. C, Mn, Si, P are required. Empty Cr, Mo, V, Ni, Cu are counted as 0.

03 · WELDING PARAMETERS (FROM THE WPS)

The result is advisory and does not replace the WPS, procedure qualification or the decision of the welding coordinator (IWE/IWT). HD and Q values are examples: enter them from your own WPS.

ACCEPTANCE DECISION

pending

Enter the chemical composition

    CEV (IIW)

    –

    –

    C + Mn/6 + (Cr+Mo+V)/5 + (Ni+Cu)/15

    CET · PREHEATING

    –

    –

    Tp min. –

    EN 1011-2, annex C, method B

    GALVANIZING REACTIVITY · ISO 14713-2

    –

    –

    Si + 2.5·P: –

    INSPECTION DOCUMENT · EN 1090-2

    –

    –

    ENTRY FOR THE FPC CARD

    Fill in the data to generate the entry.
    Sources and calculation assumptions
    • CEV = C + Mn/6 + (Cr+Mo+V)/5 + (Ni+Cu)/15 (IIW formula; EN 1011-2, annex C, method A; EN 10025-2).
    • Max. CEV from the ladle analysis per EN 10025-2 for t ≤ 30 mm: S235 0.35; S275 0.40; S355 0.45. For t > 30 mm the standard allows other values, so the engine does not issue a CEV verdict then.
    • CET = C + (Mn+Mo)/10 + (Cr+Cu)/20 + Ni/40; Tp = 697·CET + 160·tanh(d/35) + 62·HD0.35 + (53·CET − 32)·Q − 328 [°C] (EN 1011-2, annex C, method B). The engine flags when a parameter is outside the range of validity of the formula.
    • Categories A–D per EN ISO 14713-2:2019, Table 1: A: Si ≤ 0.03 % and Si + 2.5·P ≤ 0.09 %; C (Sandelin): 0.03 % < Si < 0.14 %; B (Sebisty): 0.14 % ≤ Si ≤ 0.25 %, reactivity rises at P > 0.035 %; D: Si > 0.25 %.
    • Inspection document: minimum document type required for the EXC class per EN 1090-2, Table 1, in the simplified form used in the system (EXC1: 2.2; EXC2–EXC4: 3.1).

    System modules

    Complete quality control

    From the warehouse gate to the dossier for the notified body.

    Free, no registration VTMTUTPTRTWPSWPQRNCRPZ

    Free quality and welding document templates to print

    Interactive printable templates: VT, MT, UT, PT and RT reports, a WPS card, a WPQR record, an NCR, a material receiving card (PZ) and claims for zinc and paint coatings. Fill them in your browser or print a blank form for the shop floor. In Polish, English and German; your data stays in your browser.

    Open the free templates

    In StalGuard PRO the NDT report and WPS card are built from the certificate register: heats, products and grades are already in the table, and NDT personnel fill in the examination columns (method, scope, standard, result). Try it in the free TRIAL (14 days, 10 analyses, watermark on PDF).

    Order a free TRIAL

    EN 10204 inspection documents

    Reading of 2.1, 2.2, 3.1 and 3.2 documents (including scans), sorting, comparison with the order and the product standard (Re, Rm, A, composition), FPC decision: release or NCR.

    Traceability per EN 1090-2

    Linking the product to the heat (clauses 5.2 and 5.6), QR labels that survive workshop conditions, eliminating grade mix-ups in the yard and at cutting.

    Welding engineering (IWE / RWC)

    CEV and CET per EN 1011-2 (methods A and B), preheating temperature accounting for thickness, diffusible hydrogen and heat input from the WPS/pWPS, galvanizing suitability per ISO 14713-2.

    FPC supervision and digital dossier

    Receiving and heat register ready for audit (EN 1090-1, EN ISO 3834), validity of welder qualifications per EN ISO 9606-1, VT reports per EN ISO 17637.

    Data from your certificates: firm rules

    Your certificates do not train AI models and the document content does not reach the server logs.

    See the rules

    Data and privacy

    Data from your certificates: firm rules

    Data from your certificates: firm rules

    • Your certificates do not train AI models. Every request to the OpenRouter API enforces the policy data_collection: deny: it goes only to providers that do not collect user data, i.e. do not store it permanently and do not train models on it.
    • The document content is neither logged nor archived on the server. Page images and the extracted text are processed only for the duration of the analysis; heat numbers, parameters and supplier data from the document do not end up in the server’s technical logs.
    • The analysis log contains metadata only: the file name (as given by the user), SHA-256 hash, number of pages, category and analysis status.
    • The FPC register is your decision: entries you save in the register (e.g. heat number, grade, parameters, mill) and your approvals go to the licence’s immutable audit trail (hash chain, 10 years) – this is a condition of traceability at an audit (EN 1090, ISO 3834). The trail belongs to your licence (other licences cannot see it) and is not used to train AI models.
    • Exceptions only on your action: a certificate photo submitted in photo verification mode goes to an encrypted archive (AES-256-GCM), and an SOS report with an attached document (with your consent) is deleted after 30 days.
    • Local on your machine: Excel registers, generated reports and the PDF archive. The server runs in the EU (Germany), the connection is encrypted (HTTPS); analysis and licence activation require internet access. The licence key is protected on the computer (DPAPI).
    • Payments are processed by Paddle (Merchant of Record). You buy the licence from Paddle (Paddle.com Market Limited, 30 Old Bailey, London EC4M 7AU, United Kingdom; for customers in the USA and Canada Paddle.com Inc. and Paddle.com (Canada) Ltd.), which as the merchant of record processes the transaction: payment details, invoice details (company name, address, VAT number), e-mail address, country and IP address. Paddle processes this data as a separate controller under its own privacy policy. The Supplier does not see your card number; from Paddle it receives the data needed to issue the licence, handle the order and settle accounts (e.g. e-mail address, company name, country, plan and subscription status).

    Pricing

    Choose a plan. Start with the free TRIAL.

    TRIAL: 14 days or 10 analyses. Full features, with a watermark on PDF documents and masked heat numbers. Requires a business e-mail address.

    Order a free TRIAL
    Monthly Yearly

    Standard

    For a single QC workstation. 80 certificates per 30 days.

    129 USD net

    / month

    Pricing based on billing country

    • 80 certificate analyses / 30 days · 1 workstation
    • Verification of reading consistency and a register meeting EN 1090 requirements
    • Main Steel Register, bolt and welder registers in Excel
    • CEV / CET calculators, galvanizing (ISO 14713-2) and paint shop
    • Material receiving card (PDF)
    • Polish interface, documents in PL / EN
    Ask about Standard
    Most popular

    PRO Eksport

    For fabricators and QC departments. 300 certificates per 30 days.

    339 USD net

    / month

    Pricing based on billing country

    • 300 certificate analyses / 30 days · 3 workstations
    • Everything in Standard
    • WPS / WPQR module: qualification range per EN ISO 15614-1, heat input per EN 1011-1, WPS card (PDF)
    • Approver list with PIN and audit trail report
    • Interface and documents in PL / EN / DE
    Ask about PRO Eksport

    Enterprise Global

    For groups and exporters. 1000 certificates per 30 days.

    649 USD net

    / month

    Pricing based on billing country

    • 1000 certificate analyses / 30 days · 10 workstations
    • Everything in PRO Eksport
    • Interface and documents in 15 languages
    • Your own logo on issued documents
    Ask about Enterprise Global

    All prices are net (excl. VAT). The amount and currency (PLN, EUR or USD) come from the Paddle payment system and depend on the payer's country; the payment window shows the same amount. Yearly billing: a 12-month licence for the price of 10, paid upfront for the year. The analysis limit renews every 30 days. The same document resubmitted within 7 days does not use another credit.

    Free verification

    Send 3 certificates. We will return an FPC card with a weldability analysis.

    You will get the document verification result, CEV/CET, galvanizing suitability and a proposal to release or issue an NCR, in a form you can show at an audit.

    Want a trial period? Put “TRIAL” in the subject and give your company name; the trial requires a business e-mail address (14 days, 10 analyses, watermark on PDF).

    kontakt@stalguard.pl

    Engineering consultations: Mon–Fri, 8:00–16:00 (Polish time)

    Supplier / System information

    A system for steel fabricators covered by FPC per EN 1090-1/-2 (EXC1–EXC4) and welding quality requirements per EN ISO 3834.

    Supplier: Marek Nowicki (natural person), ul. Henryka Sienkiewicza 14/2, 62-069 Dąbrowa. Payments are processed by Paddle (Merchant of Record).

    © 2026 StalGuard PRO

    Terms and Refund Policy

    Privacy policy / GDPR

    Data controller and website visits. The controller of data processed in connection with the website, contact and the licence is Marek Nowicki (natural person), ul. Henryka Sienkiewicza 14/2, 62-069 Dąbrowa (contact: kontakt@stalguard.pl). The website does not load analytics or advertising tools. When it opens, your browser loads the Paddle script (cdn.paddle.com) and asks Paddle for prices for your country, so Paddle receives your IP address and technical browser data even if you do not buy; Paddle may also store its own cookies or local storage (e.g. to prevent abuse). You have the right of access, rectification, erasure, restriction and objection, and to lodge a complaint with the supervisory authority; send requests to the contact address.